Real Time Design Of Steel Structures Design Interview Questions with Answers PDF
1. What Is Structural Steel Design?
structural steel design, is an area of knowledge of structural engineering used to design steel structures. The structures can range from schools to homes to bridges. ... The second is the Load and Resistance Factor Design (LRFD) method.
2. What Are The Mechanical Properties Of Structural Steel?
Resistence to deformation based upon:
Material.
Length.
X-section.
3. Explain The Design Process Of Structural Steel?
Design process :
Preliminary member sizing of beams
Structural analysis - modeling, analysis
Design review - member modifications
Cost of estimation
Preparation of structural drawings and specifications
Loads for structural analysis and design
Dead load
Live load
Mean return period OR
Recurrence interval OR
Live loads for various occupencies
Reduction in basic design live load
Impact Load
Wind load
4. Describe The Steps Used For Erection Of Structural Steel?
Material received at site.
Concrete bases and anchor bolts.
Shims.
Pre assembly at ground level.
Main construction steel erection (dimension bolt)
Tightening for anchor bolt.
Alignment for structural steel.
Tightening for steel.
Tightening for anchor bolts.
Grouting.
Complete structural steel erection (secondary beams, bracing).
Calibration of whrench and device.
Modification during and after erection includes cutting, welding, NDT,….etc).
Painting inspection.
5. What Are The Defects You Can Except During Inspection Of Material Receiving At The Site?
Lamination.
distortion.
pitting.
6. Mention The Steps To Check Material Received At The Site?
Visual inspection.
Dimension inspection.
Verification of heat no and mill certificate information’s.
7. How Can You Check The Support Foundation ?
Location.
Orientation.
Elevation.
8. What Is The Minimum Top Elevation Of Leveling Shims?
Minimum 25mm.
9. What Is The Acceptable Variation In Dimensions Between The Centres Of Two Anchor Bolts (within An Anchor Bolt Group)?
Maximum 3 mm.
10. Which Code You Can Use For Check Bolts Used For Primary Structural Connection?
ASTM A325 N.
11. What Is The Minimum Size Of Bolt Used At Astm A32 N ?
Minimum size 20mm.
12. How Much Variation In Elevation Of The Top Of Anchor Rods?
Max 13 mm.
13. How Many Days Minimum Required To Archive 70% Concrete Strength (curing Time)?
7 days minimum.
14. How Many Bolts Minimum Required Per Connection?
2 bolt minimum required.
15. How Much Variation In Dimension From Centre Of Any Anchor Bolts Group To Be Establish Column Line Through The Group?
Equal to or less than 6mm
16. Which Code You Can Use For Welding Of Structural Steel?
D1.1.
17. What Are The Types Of Joints You Can Use For Erection Of Structural Steel?
Snugtightened joint. Pretension join or slip critical joint.
18. What Is Minimum Thickness Of Any Part Of Structural Steel Shape?
Minimum 5 mm.
19. What Is The Vertical Tolerance (alignment) For Straight Compression Structural Member?
1 mm per 1m accepted.
20. What Are The Types Of Methods Of Bolt Tightening?
Snug tightening, turn of nutpreten sioning calibrated wrench pretensioning or directtension indicator pretensioning
21. Complete, All Bolts, Nuts And Washers Shall Be Properly Identified And Marked With ?
Material grade.
manufacture’s logo.
22. all Nuts For High Strength Bolts Shall Be …………. To Reduce To Torque Installation .
Wax – dipped.
23. All Gusset And Stiffener Plates Shall Be …………..mm Minimum Thickness
10 mm minimum.
24. What Is The Minimum Height Of Handrails Provided On Walkways And Platforms ?
Over 1 meter heigh.
25. Complete, Standard Bolt Holes Shall Not Be Enlarge By More Than ……………. Mm To Make Connection Resulting From Minor Mislit
1mm.
26. What Are The Properties Of A Steel?
The important characteristics of steel for design purposes are:
yield stress (Fy).
ultimate stress (Fu).
modulus of elasticity (E).
percent elongation (e).
coefficient of thermal expansion (a).
27. What Are The Types Of Structural Steel?
Types of structural steel : Various types of structural steel sections and their technical specifications are as follows:
Beams.
Channels.
Angles.
Flats
28. What Are Steel Beams?
Steel Beams : Steel Beams is considered to be a structural element which mainly carries load in flexure meaning bending. Usually beams carry vertical gravitational force but are also capable of carrying horizontal loads generally in the case of an earthquake.
The mechanism of carrying load in a beam is very unique, like; the load carried by a beam is transferred to walls, columns or girders which in turn transfer the force to the adjacent structural compression members. The joists rest on the beam in light frame constructions.
29. Explain About Steel Channels?
Steel channels : Steel channels are used ideally as supports and guide rails. These are roll-formed products. The main metal used for making channels is steel along with aluminum. There are certain variations that are available in the channels category, the categorization is mainly on the shape of the channel, the varieties are mentioned below:
J channels: This kind of channel has two legs and a web. One leg is longer. This channel resembles the letter-J.
Hat channels: This channel has legs that are folded in the outward direction resembling an old fashioned man's hat.
U channels: This most common and basic channel variety. It has a base known as a web and two equal length legs.
C channels: In this channel the legs are folded back in the channel and resemble the letter-C. C channels are known as rests.
Hemmed channels: In this kind of channel the top of the leg is folded hence forming double thickness.
30. What Are The Applications Of Steel Channels?
Application : Steel channels are subjected to a wide array of applications. The application fields are:
Construction.
Appliances.
Transportation.
Used in making Signposts.
Used in wood flooring for athletic purposes.
Used in installing and making windows and doors.
1. What Is Structural Steel Design?
structural steel design, is an area of knowledge of structural engineering used to design steel structures. The structures can range from schools to homes to bridges. ... The second is the Load and Resistance Factor Design (LRFD) method.
2. What Are The Mechanical Properties Of Structural Steel?
Resistence to deformation based upon:
Material.
Length.
X-section.
3. Explain The Design Process Of Structural Steel?
Design process :
Preliminary member sizing of beams
Structural analysis - modeling, analysis
Design review - member modifications
Cost of estimation
Preparation of structural drawings and specifications
Loads for structural analysis and design
Dead load
Live load
Mean return period OR
Recurrence interval OR
Live loads for various occupencies
Reduction in basic design live load
Impact Load
Wind load
4. Describe The Steps Used For Erection Of Structural Steel?
Material received at site.
Concrete bases and anchor bolts.
Shims.
Pre assembly at ground level.
Main construction steel erection (dimension bolt)
Tightening for anchor bolt.
Alignment for structural steel.
Tightening for steel.
Tightening for anchor bolts.
Grouting.
Complete structural steel erection (secondary beams, bracing).
Calibration of whrench and device.
Modification during and after erection includes cutting, welding, NDT,….etc).
Painting inspection.
5. What Are The Defects You Can Except During Inspection Of Material Receiving At The Site?
Lamination.
distortion.
pitting.
6. Mention The Steps To Check Material Received At The Site?
Visual inspection.
Dimension inspection.
Verification of heat no and mill certificate information’s.
7. How Can You Check The Support Foundation ?
Location.
Orientation.
Elevation.
8. What Is The Minimum Top Elevation Of Leveling Shims?
Minimum 25mm.
9. What Is The Acceptable Variation In Dimensions Between The Centres Of Two Anchor Bolts (within An Anchor Bolt Group)?
Maximum 3 mm.
10. Which Code You Can Use For Check Bolts Used For Primary Structural Connection?
ASTM A325 N.
11. What Is The Minimum Size Of Bolt Used At Astm A32 N ?
Minimum size 20mm.
12. How Much Variation In Elevation Of The Top Of Anchor Rods?
Max 13 mm.
13. How Many Days Minimum Required To Archive 70% Concrete Strength (curing Time)?
7 days minimum.
14. How Many Bolts Minimum Required Per Connection?
2 bolt minimum required.
15. How Much Variation In Dimension From Centre Of Any Anchor Bolts Group To Be Establish Column Line Through The Group?
Equal to or less than 6mm
16. Which Code You Can Use For Welding Of Structural Steel?
D1.1.
17. What Are The Types Of Joints You Can Use For Erection Of Structural Steel?
Snugtightened joint. Pretension join or slip critical joint.
18. What Is Minimum Thickness Of Any Part Of Structural Steel Shape?
Minimum 5 mm.
19. What Is The Vertical Tolerance (alignment) For Straight Compression Structural Member?
1 mm per 1m accepted.
20. What Are The Types Of Methods Of Bolt Tightening?
Snug tightening, turn of nutpreten sioning calibrated wrench pretensioning or directtension indicator pretensioning
21. Complete, All Bolts, Nuts And Washers Shall Be Properly Identified And Marked With ?
Material grade.
manufacture’s logo.
22. all Nuts For High Strength Bolts Shall Be …………. To Reduce To Torque Installation .
Wax – dipped.
23. All Gusset And Stiffener Plates Shall Be …………..mm Minimum Thickness
10 mm minimum.
24. What Is The Minimum Height Of Handrails Provided On Walkways And Platforms ?
Over 1 meter heigh.
25. Complete, Standard Bolt Holes Shall Not Be Enlarge By More Than ……………. Mm To Make Connection Resulting From Minor Mislit
1mm.
26. What Are The Properties Of A Steel?
The important characteristics of steel for design purposes are:
yield stress (Fy).
ultimate stress (Fu).
modulus of elasticity (E).
percent elongation (e).
coefficient of thermal expansion (a).
27. What Are The Types Of Structural Steel?
Types of structural steel : Various types of structural steel sections and their technical specifications are as follows:
Beams.
Channels.
Angles.
Flats
28. What Are Steel Beams?
Steel Beams : Steel Beams is considered to be a structural element which mainly carries load in flexure meaning bending. Usually beams carry vertical gravitational force but are also capable of carrying horizontal loads generally in the case of an earthquake.
The mechanism of carrying load in a beam is very unique, like; the load carried by a beam is transferred to walls, columns or girders which in turn transfer the force to the adjacent structural compression members. The joists rest on the beam in light frame constructions.
29. Explain About Steel Channels?
Steel channels : Steel channels are used ideally as supports and guide rails. These are roll-formed products. The main metal used for making channels is steel along with aluminum. There are certain variations that are available in the channels category, the categorization is mainly on the shape of the channel, the varieties are mentioned below:
J channels: This kind of channel has two legs and a web. One leg is longer. This channel resembles the letter-J.
Hat channels: This channel has legs that are folded in the outward direction resembling an old fashioned man's hat.
U channels: This most common and basic channel variety. It has a base known as a web and two equal length legs.
C channels: In this channel the legs are folded back in the channel and resemble the letter-C. C channels are known as rests.
Hemmed channels: In this kind of channel the top of the leg is folded hence forming double thickness.
30. What Are The Applications Of Steel Channels?
Application : Steel channels are subjected to a wide array of applications. The application fields are:
Construction.
Appliances.
Transportation.
Used in making Signposts.
Used in wood flooring for athletic purposes.
Used in installing and making windows and doors.
1 comment:
Hey! I have read all your Blog this So Nice and Awesome service you have provided, I learn many new things from here and want implement my website.
Electrical Services in Clapham
Post a Comment